Dvs -30-2 Bedienungsanleitung PDF herunterladen (Seite 27)

13369-1-0203 Page 27

PIEZO IGNITOR

VALVE CONTROL KNOB

VARIABLE REGULATOR

("HI"-"LO") KNOB

REMOTE/ON/OFF SWITCH

DOOR ASSEMBLY (SHOWN OPEN)

GAS VALVE

Figure 49

Initial Lighting

Upon completing the gas line or turning the gas valve on after it

has been in the "OFF" position, a small amount of air will be in

the lines. When first lighting the fireplace, it will take a few

minutes for the lines to purge themselves of this air. Once the

purging is complete, the fireplace will light and operate

satisfactorily.

Subsequent lightings of the appliance will not require such

purging if the gas valve is not turned to "OFF."

Pilot Flame (Figure 50)

The thermopile/thermocouple (standing pilot) tips should be

covered with flame.

Figure 50

STANDING PILOT OPERATING INSTRUCTIONS

ON/OFF/REMOTE Switch

DVS is equipped with an ON/OFF/REMOTE switch. A wire

harness is attached to the ON/OFF/REMOTE switch. The red,

black and green (wires) female push-ons attach to the ON/OFF/

REMOTE switch. At the opposite end of the wire harness, the

black and green (wires) female push-ons attach to the gas valve.

An additional green wire and the red wire, which are stripped and

bare, will attach to the 750 millivolt wall thermostat accessory,

or, to one of the other accessories that can be purchased for use

with your log set.

Operation of ON/OFF/REMOTE Switch with no Accessories

To ignite main burner, turn the control knob on the gas valve from

the PILOT position to the ON position. Turn the ON/OFF/

REMOTE switch from the OFF position to the ON position. The

additional green wire and red wire, which are stripped and bare

are not used.

Operation of ON/OFF/REMOTE Switch with Accessories

750 Millivolt Wall Thermostat, GWSG-T

Connect the green and red, stripped and bare, wires on the ON/

OFF/REMOTE switch wire harness to the wall thermostat. Turn

the ON/OFF/REMOTE switch to the REMOTE position. Set the

wall thermostat to the desired temperature.

It is important to use wire of a gauge proper for the length of the

wire:

RECOMMENDED WIRE GAUGES

Maximum Wire

Length Gauge

1' to 10' 18

10' to 25' 16

25' to 35' 14

Wall Switch, FWS-1

Connect the green and red, stripped and bare, wires on the ON/

OFF/REMOTE switch wire harness to the wall switch. Turn the

ON/OFF/REMOTE switch to the REMOTE position. Pivot the

rocker switch on the FWS-1 to the ON position.

Battery Operated Remote Control, FRBC-1 and FRBTC-1

Connect the green and red, stripped and bare, wires on the ON/

OFF/REMOTE switch wire harness to the remote receiver that is

a component in the FRBC-1 and FRBTC-1. Turn the ON/OFF/

REMOTE switch to the REMOTE position. Follow instructions

in the FRBC-1 and FRBTC-1 to complete installation.

Note: If batteries fail in FRBC-1 or FRBTC-1, and immediate

heat is desired, turn the ON/OFF/REMOTE switch from the

REMOTE position to the ON position.

Electric (120 volt) Operated Remote Control, FREC-1

Connect the green and red, stripped and bare, wires on the ON/

OFF/REMOTE switch wire harness to the wires on remote

receiver that is a component in the FREC-1. Turn the ON/OFF/

REMOTE switch to the REMOTE position. Follow instructions

in the FREC-1 to complete installation.

Note: If electric (120 volt) fails in FREC-1, and immediate heat

is desired, turn the ON/OFF/REMOTE switch from the REMOTE

position to the ON position.

Wiring of ON/OFF/REMOTE Switch with 750 Millivolt Wall

Thermostat Accessory and Another Accessory

Connect the green and red, stripped and bare, wires on the ON/

OFF/REMOTE switch wire harness to the 750 millivolt wall

thermostat AND to the remote receiver that is a component in the

FRBC-1, FREC-1 OR to the FWS-1, wall switch.

1. Connect (1) wire from the 750 millivolt wall thermostat and (1)

wire from appropriate accessory to the GREEN, stripped and

bare wire from the ON/OFF/REMOTE wire harness.

2. Connect (1) wire from the 750 millivolt wall thermostat and (1)

wire from appropriate accessory to the RED, stripped and bare

wire from the ON/OFF/REMOTE wire harness.

Note: When the appliance is in the MANUAL mode and the

batteries fail in the FRBC-1 or if the electric (120 volt) fails in

the FREC-1, and immediate heat is desired, turn the ON/OFF/

REMOTE switch from the REMOTE position to the ON

position.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

Dvs -30-2 Bedienungsanleitung Seite 27

Kommentare zu diesen Handbüchern